SUN MACHINE 500 Serial B Automotive Service Equipment PDF Operators Manual

The Installation Instructions listed are for the SUN MACHINE 500 Serial B (220 VAC). The unit is shipped as a fully assembled unit with the exception of the items listed in the PARTS & ACCESSORIES LIST. To
insure that the most recent release of operating software is received, the software will be added to the unit before it is shipped to the customer.

INSTALLATION INSTRUCTIONS: 1. Cut straps, and remove top of carton.
2. Cut the sides of the carton at the taped seams and remove the sides.
3. Look for Software Package shipped with the unit and set aside. The software envelope is pushed into the slot cut in to the shipping carton.
4. Remove foam packing from around the sides of the unit.
NOTE: Steps 5 through 8 will require two or more people.
5. Look at the foam pieces on the bottom of the unit, the longest piece should be on the left-hand side (looking at the unit from the front). On the left side break down the cardboard bottom.
6. Starting from the left side of the Tester, with the foam pieces still under unit carefully slide the unit from the pallet moving from right to the left (looking at the unit from the front).
7. Lean the Sun Machine so that half of the foam base can be removed.
8. Lean the Sun Machine so that other half of the foam base can be removed.
9. Remove tape from ALL drawers and covers.
10. Pull the keyboard, keyboard drawer out, and remove bubble wrap. Slide the keyboard back in.
11. Inventory all items using the parts listed: inspect for damage. The Unit Accessories are located in the bottom drawer of the unit. The Literature Kit is located the in middle drawer.
NOTE: Any owner’s manuals or software that comes with the computer components are located in the upper drawer of the unit.
NOTE: Any REGISTRATION CARDS for the installed software such as Microsoft® Windows 95 must be filled out and sent in by the customer to ensure compliance with any software licensing agreements.
12. Locate the four hangers (2161-0023) and the four 10-32 x ½” thread forming screws (1-7726). Attach two hangers to the left side and two to the right side of the unit using the hex screws.
13. The Monitor is shipped separately from the unit. Remove the Monitor from the box and inspect the monitor for damage.
14. Remove the swivel base and the rear plastic protector from the ACER monitor and discard. Refer to figure 1, below. If you have a Sampo monitor, just remove the swivel base if attached.

15. Place the monitor into the monitor base plate with the back of the monitor pushed snug against the back bracket. Slide the front bracket snug up to the front of the monitor and tighten the nuts of the brackets.
16. Fasten the Velcro straps over the top of the monitor and snug down.
17. Discard the A.C. Cable supplied with the Monitor. Use the A.C. Cable (EAW0096C00A) found in the unit accessories.
18. Connect monitor power cable and data cable to the unit.
19. On the back of the unit under the monitor there is a cable clamp. Use the cable clamp for the monitor data cable, leave room for the monitor to swivel left and right 90 degrees off center.
20. Locate the Mouse and install the Mouse cable end to COM 2 connector, of the connector plate on the back of the unit.
21. Locate the printer paper in the upper storage drawer. Load printer paper into paper cassette of the Printer (100 Sheets maximum). A portion of the remaining paper can be placed under the Printer.
22. Connect all Test Leads along with the Vacuum Hose, to their respective connectors located on the boom of the Sun Machine. Store any unused leads and accessories in one of the storage drawers.
23. Locate the Oxygen Sensor (7049-0004-01) in the accessories bag, open the back panel door of the tester. Remove the Oxygen Sensor Cover from the IR Drawer, install the Oxygen Sensor into the block and connect the wiring harness to the top of the sensor. Reinstall the cover over the sensor and mounting block.

Download SUN MACHINE 500 Serial B Automotive Service Equipment PDF Operators Manual


Related E-Books:

    None Found

March 17, 2010 | Posted in Electronic Manual, Others

Comments

One Response to “SUN MACHINE 500 Serial B Automotive Service Equipment PDF Operators Manual”

  1. ahmed ibrahim on May 23rd, 2011 2:57 pm

    i want new version of sun machine

Leave a Reply




wireless credit card terminal reviews