Scribe Ec With Primera Pro Printer PDF Installation Guide

Minimum PC System Requirements
• A Pentium II/III PC 800 MHz or faster
• Windows 2000 Pro (Service Pack 4.0) or Windows XP
• 512 MB Ram
• 7200 RPM ATA-100 Clean Hard Disk NTFS – (5GB Free Space)
• 800 x 600 display, 16-bit color recommended
• Two Button Mouse
• Two Free PCI Slots
• 1 external COM port (COM1 or COM2) – 2 ports needed if using Prism Plus or Spectrum2
• Win ASPI driver layer (Included)
• IEEE-1394s adapters (Included) (Except print Station)
• Appropriate IEEE-1284 Printer Cable if attached

One and two drive ScribeECs require one IEEE-1394 card. Four drive systems require two IEEE-1394 cards.
1. Shut down the PC.
2. Turn the PC’s power off.
3. Unplug the PC.
4. Remove the PC’s cover as indicated in the PC’s manual.
5. Locate an empty PCI slot, as seen in (fig.1).
6. Install the firewire adapter card (fig. 2).

Installing the Drive Bay
1. Place the drive bay onto the base unit as seen in (fig. 1).
2. Position the drive bay so that the front right corner sits over the dotted line (fig. 2). Proper position is shown in (fig. 3).

Preparing The Signature PRO Inkjet Printer What’s In The Box
• Signature PRO printer
• Signature PRO printer adapter plate
• Power adapter
• Printer software CD
• Color ink cartridge
• Spare ink cartridge holder
• Warranty statement and registration card
• Operator’s manual

Installing the Signature PRO Printer Adapter Plate
1. Using needle nose pliers, remove the rubber feet from the bottom of the printer (fig. 1).
2. Screw the printer plate to the bottom of the inkjet printer as seen in (fig. 2).

Installing the SCRIBE EC Alignment Utility
1. Insert the SCRIBE CD into the CD-ROM drive of your PC.
2. Click on setup.exe of the alignment utility and Click OK (fig. 1).
3. Click the button indicated in (fig. 2).
4. Enter a name for the group where the Alignment Utility will be located. Click Continue (fig. 3). The Scribe Program Utility will appear
under Start / Programs / ”group name” after installation is complete.
5. A progress bar will appear (fig. 4).
6. Click OK (fig. 5) to finish installation.

Installing the Signature PRO Printer Driver
1. Click Start-> Settings-> Printers
2. Click Add New Printer
3. The “Welcome to the Add Printer Wizard” window will appear (fig 1). Click Next.
4. In the “Local or Network Printer” window, uncheck the “Automatically detect installed printer” option , leaving the “Local printer attached to
computer” option (fig 2) and click Next..
5. In the “Select a Printer Port” window, leave the default as LPT1 (fig 3) and click Next.
6. In the “Install Printer Software” window, click the “Have Disk” button (fig 4). You will then be prompted to “Install from Disk”, click the “Browse” button (fig 5). Select the location of the printer driver from your CD-ROM drive in the PC (fig 6).
7. After specifying the driver for the Signature PRO printer, the printer “CD Color Printer PRO” will appear in the “Add Printer Window” (fig 7). Click Next to continue.
8. In the “Name your Printer” window, leave the printer as the default name, and select the printer to be the default printer (fig 8) and click Next.
9. In the “Printer Sharing” window, select “Do Not Share the Printer” (fig 9) and click Next.
10. Say No to “Print Test Page” (fig 10) and click next.
11. The “Completing the Add Printer Wizard” window will appear (fig 11). Click Finish. After clicking finish, the Signature PRO printer driver will be
installed. You will be asked to accept that the printer driver is not digitally signed by Microsoft, click Continue (fig 12). You have now successfully installed the printer.

Download Scribe Ec With Primera Pro Printer PDF Installation Guide


Related E-Books:

    None Found

June 20, 2010 | Posted in Electronic Manual, Printer

Comments

Leave a Reply