OAsys / iPAD Kitchen Display Systems PDF Product Manual Guide

EV1000 /AV1000 CARD
The newer AV1000 cards can be used instead of or in conjunction with EV1000 cards. The jumpers, settings, and connectors mimic those on the EV1000 card. OAsys Cover Removal Remove all four cover screws. Two screws are located on each side panel of the top cover. OAsys Base Unit Configuration Each OAsys Unit is preset for plug-n-play operation at the factory. It may be wise to visually check the required settings are intact,
especially when servicing or replacing base units. Below are the designated settings for proper OAsys KDS operation. Factory settings are in BOLD.
Video ID Number Unique selection one for each EV1000 card installed

SK9200 Cover Removal To remove the top cover on the SK9200 bump bar carefully insert a flat screwdriver tip at the slotted end of the unit and
twist the screwdriver tip until the SK9200 top cover lifts out of its hold position. Then, slowly pry open the top cover and place on a flat surface –
excercising care not to crease or damage the key matrix ribbon cable. SK9200 Configuration Each SK9200 bump bar is pre-set for plug-n-play operation at the factory. It may be wise to visually check the required settings are intact, especially when servicing or replacing bump bar devices. The following table lists the designated settings for proper SK9200 bump bar use for OAsys KDS operation. Factory settings are in BOLD.

SPEAKER VOLUME Adjust to suitable SPEAKER volume.
Key Template Orientation
The SK9200 bump bar is supplied with a double sided, removable key template. The template provided offers key labels for most common KDS usage. It will display key labels for viewing in a horizontal bump bar mounting position or a vertical mounting position. The bump bar comes factory oriented for horizontal mounting, but can easily be switched to display vertical key labels as follows:
1) Remove the bump bar top cover as instructed above.
2) Locate the key template tab on the back of the bump bar top cover. Grab the tab, and slide out the template.
3) Holding the template tab, reinsert the template with the vertical key labels visible through the key windows on the top of the bump bar cover.
Connect bump bar RJ45 cable into designated jack on SK9200 circuit card, for routing to EV1000 card in OAsys enclosure.

When configuration and cable connection for the SK9200 bump bar is completed, ensure that the SK9200 key matrix ribbon cable is in place, the communications cable is connected to the RJ45 jack, the rubber cable grommet is also in place, then firmly secure top cover. If you are unsure of the appropriate speaker volume needed at this time, upon final installation and power up, adjust the speaker volume to desired level. Secure top
cover after this adjustment is made.

PC3860 PROCESSOR CARD
There are no user-selectable options necessary for configuring the PC3860 processor card. This card is plug-n-play ready for operation as supplied from the factory for the base OAsys operation. Future optional features will be provided, as needed, which may affect these factory defaults.

GREEN [LED ON] To indicate the link integrity between the adapter and the twisted-pair hub. The LED remains on while the network cable’s link
integrity is good. Hardware Installation Each ESL-186 Card is pre-set for plug-n-play operation at the factory. Remove all four cover screws to the Oasys unit encloser. Two screws are located on each side panel of the top cover. Insert the ESL-816 card into an available slot on the motherboard, and secure card bracket to enclosure with mounting screw. When the card is mounted firmly secured to the OAsys base unit chassis, screw down the enclosure cover.

Thin Ethernet Cable
1. Connect the T-connect.or to the card’s BNC connector.
2. Connect the Thin coaxial cable to the T-connector. Note: If you are installing a station at the end of a cable segment, you need 50-ohm
cable terminators at both ends of the cable segment (one end must be grounded). Twisted-Pair Cable
1.Insert the RJ-45 connector into the UTP jack on the adapter.
2.Connect one end of the UTP cable to a 10BASE-T HUB Once the hardware is installed, initialize your software (refer to software vendor instructions) to complete installation

1) Plug in monitor power cords into AC outlet and apply power to each monitor.
2) Plug in OAsys base unit power supply to AC outlet. NOTE: If properly installed, The OAsys power LED’s (+5V, +12V, & -12V) should illuminate,
each bump bar should visibly show an illuminated green light and sound a single 1-second ‘beep’ when then OAsys unit is powered up. Also, each
monitor should display a visible start-up screen within a few seconds. If the proper response is not confirmed, refer to the TROUBLESHOOTING
section of this manual for advice.
3) For normal operation, the video monitor used as DISPLAY #1 will report when the OAsys KDS start-up is ready. From the bump bar, press the FUNC key to switch to the site menu. At this menu, you can test the bump bar, display set up configuration, and monitor network activity. Instructions for menu operation are supplied on the menu screen. To resume to normal screen mode, press ESC key.
4.) Once all devices are confirmed to be operationally powered on, the PC (POS) can be powered on and the KDS software can be installed.
(See KDS Software documentation for proper software installation, configuration, and operation…

Download OAsys / iPAD Kitchen Display Systems PDF Product Manual Guide


Related E-Books:

    None Found

February 26, 2010 | Posted in Electronic Manual, Software

Comments

Leave a Reply