Lenovo C500 Projector PDF User’s Guide Manual

Positioning the projector
To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Following are some general guidelines: v Position the projector on a flat surface at a right angle to the screen. The projector must be at least 1.5 m (4.9 ft) from the projection screen. v Position the projector within 2.7 m (9 ft.) of your power source and within 1.8 m (6 ft.) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within .15 m (6 in.) of a wall or other object. v Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.

Connecting devices
Computers and video devices can be connected to the projector at the same time. Check the user’s manual of the connecting device to confirm that it has the appropriate output connector.

Connecting to a USB device
To control your computer mouse using the projector remote control, connect the projector to the computer with a USB cable as shown below. The USB mouse function is only supported with Microsoft® Windows® 2000 and Windows XP operating systems.

Operating range
This remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote to the sides or the rear of the projector, the remote will function within a maximum radius of 10m (33ft) and 30° above or below the projector level. If the projector does not respond to the remote control, move closer. Note: You can also point the remote at the projected image. Projector and remote control buttons The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control. The figure below shows the corresponding buttons on the remote control and on the projector for OSD menu operation. Some buttons have two functions. For example, item 3/5 on the projector functions both as the keystone button and as the up cursor key in OSD menus.

Quality menu
The Quality menu can be found through the main menu. To access the Quality menu,
1. Press the Menu button to open the OSD.
2. Press the left or right cursor button to move to the Quality menu.
3. Press the up or down cursor button to move up and down in the Quality menu.
4. Press the left or right cursor button to change values for settings.
5. Press the up or down cursor button to select a different Quality menu item for change.
6. If you wish to cancel all changes made within the Quality menu, select Cancel and press the Enter button.
7. Press Menu to confirm the new settings and leave the Quality menu.

Properties menu To access the Properties menu, Press the Menu button to open the OSD.
1. Press the left or right cursor button to move to the Properties menu.
2. Press the up or down cursor button to move up and down in the Properties menu.
3. Press the left or right cursor button to change values for settings.
5. Press the up or down cursor button to select a different Properties menu item for change.
6. If you wish to cancel all changes made within the Properties menu, select Cancel and press the Enter button.
7. Press Menu to confirm the new settings and leave the Properties menu.

Advance Feature menu
To access the Advance Feature menu,
1. Press the Menu button to open the OSD.
2. Press the left or right cursor button to move to the Properties menu.
3. Press the up or down cursor button to move to the Advance Feature menu and then press Enter button.
4. Press the up or down cursor button to move up and down in the Advance Feature menu. Press the left or right cursor button to change values for settings. Press the up or down cursor buttons to select a different Advance Feature menu item for change.
5. If you wish to cancel all changes made within the Advance Feature menu, select Cancel and press the Enter button.
6. Press Menu to confirm the new settings and leave the Advance Feature menu.

Network setup
When connected to a local area network (LAN) through the RJ-45 connector, the projector can be controlled remotely through a Web browser by any of the clients (PCs connected to the LAN) on the LAN. The projector can also be accessed outside the LAN, with a correctly configured firewall.

Download Lenovo C500 Projector PDF User’s Guide Manual


Related E-Books:

    None Found

May 26, 2010 | Posted in Lenovo Manual, Projector Manual

Comments

Leave a Reply