Honeywell CM907 Programmable Thermostat PDF Product Specification Sheet Manual
The CM907 thermostat is designed to provide automatic time and temperature control of heating or cooling systems in villas and apartments.
It can be used as part of a system in conjunction with combiboilers, oil-burners and gas fired boilers, circulation pumps, thermal actuators, zone valves and electric heat systems (<8A). The CM907 is designed with the installer in mind and includes a moulded back-plate with trunking guides and wiring breakouts to make installation quick and easy. The CM907 extra large LCD display, dynamic text display, button layout based on the same simple programming philosophy used on our acclaimed CM60 products and the introduction of an ‘OK’ button, makes it easier to install and
more user friendly. The unit is ideal for consumers who want reliable precise temperature control from a modern looking, simple to program and easy to use product.
July 8, 2010 | Posted in Honeywell Manual, Thermostats | Leave a Comment
Honeywell CT3500/CT3595 Programmable Thermostat PDF Owners Guide
Test your heating and cooling systems to make sure they work properly. If either system does not work, contact your local heating/air-conditioning dealer. To avoid compressor damage, do not operate the cooling system when outdoor temperature is below 50°F (10°C). Turn off power to the system at the furnace or the fuse/circuit breaker panel. Carefully unpack your new thermostat and wallplate. Save package of screws, instructions, and receipt. Remove the cover from the old thermostat. If the cover does not snap off when pulled firmly from the bottom, check for a screw or screws used to lock on the cover. Loosen the screw or screws holding the thermostat to the wallplate and lift the thermostat away. Disconnect the wires from the old thermostat. As you disconnect each wire, attach the enclosed labels with the old terminal designation. If there are only two wires, they do not need to be labeled. Wrap the wires around a pencil as shown to keep them from falling back into the wall.
July 8, 2010 | Posted in Honeywell Manual, Thermostats | Leave a Comment
Honeywell CM67RF Wirefree Chronotherm PDF Product Specification Sheet Manual
The CM67RF Chronotherm is designed to provide automatic time and temperature control of heating or cooling systems in villas and apartments. It can be used as part of a system in conjunction with gas and oil boilers, circulation pumps, variety of valves and actuators or electric heating systems (<10A). The radio frequency controlled CM67RF system consists of a room unit T6667C and relay box R6660C (HC60). No wiring to the room unit is required. Installer needs to wire only the relay box to a controlled device (e.g. boiler) and mount the room unit in a suitable location where the RF communication is reliable. The CM67RF display, buttons and slider layout are identical to CM67 ‘wired’ chronotherm The unit is ideal for consumers who want reliable precise temperature control from a simple to program easy to use product.
July 8, 2010 | Posted in Honeywell Manual, Thermostats | Leave a Comment
Honeywell CM900 Programmable Room Thermostat PDF Installation Guide
Setting-up the Thermostat
Please follow the illustrations detailed on page 1 in sequence to install the thermostat correctly, then refer to the steps below:
NOTE: For gas boiler applications, the factory system settings will not need to be changed (for other applications see section ‘Using the Thermostat for Specific Applications’ below).
July 3, 2010 | Posted in Electronic Manual, Honeywell Manual | Leave a Comment
Honeywell NetAXS NX4S1 Access Control Unit PDF Installation Guide
An access control system protects and preserves an enterprise’s resources by providing authentication, authorization, and administration services. Authentication is a process that verifies a user’s identity. If the user is verified, the system then either grants or denies access to specific areas and resources. Administration includes the creation and modification of user accounts and access privileges. An access control system consists of hardware and software, usually configured in a network environment over a standard network protocol. Access control units, readers, door strikes, and video and other devices, for example, are configured to control and monitor the access to a company site. The NX4S1 access control unit consists of a NetAXS™ panel control board and battery. The components are enclosed in a pre-wired cabinet. The 16.5 VAC power supply (Basler Electric Model BE156250CAA0004, M&G Electronics Model MGT1650, or Honeywell Access Systems part number X-4) provides power for the panel control board, which is a four-reader panel providing access control for up to four doors. The following figure shows the NX4S1 panel components.
July 2, 2010 | Posted in Electronic Manual, Honeywell Manual | Leave a Comment
Honeywell NS1 Access Control Application PDF Installation Guide
Thank you for using NS1 for your access control application. NS1 is a powerful access control system which can be used for single door access, as well as for connection to any type of on-line access control system. NS1 units can also be mounted in an RS485 network without the necessity of an external access control system. NS1 as a single door unit offers many possibilities such as:
• Access control
• Unlock option
• Day/Nightlock option (manual or automatic switching)
• Long range reader (up to 45cm)
• Optional use of PIN keypad
• Using an external relay (to prevent potential tampering)
• NS1 Manage software for stand-alone PC programming, event logging and user database maintenance
July 2, 2010 | Posted in Electronic Manual, Honeywell Manual | Leave a Comment
