Toshiba Blu-ray Disc Player BDX2500KU PDF Owners Manual
Your Blu-ray disc player can be connected to your home network:
• By connecting an Ethernet cable to the ETHERNET jack on the rear of your player and to a wired hub or router. Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference.
Connecting your player to a wired router:
• Connect an Ethernet cable (CAT5 or better with RJ45 connector) to the ETHERNET jack on the back of your player and to an Ethernet jack on a hub or broadband router.
Notes:
• Do not connect a modular phone cable to the ETHERNET jack.
• When plugging or unplugging the cable, hold the connector on the end of the cable. When unplugging, do not pull on the cable. Press down the lock tab and pull the connector out of the jack.
• Because there are various connection configurations, follow the instructions from your telecommunication carrier or Internet service provider.
November 24, 2010 | Posted in Audio Video, Toshiba Manual, Wireless | Leave a Comment
Altec Lansing iM600 Digital Speaker PDF User Guide Manual
Thank you for purchasing the Altec Lansing iM600 digital speaker system for iPod. When Altec Lansing introduced the original inMotion, it set new standards for sound and size and let a whole lot of music out of the iPod. Today, the new iM600 raises the bar again
with an innovative and performance-leading design.
Open the inMotion iM600 by pressing the button on the front of the speaker system. Position the inMotion iM600 on a level surface, preferably close to you (within three feet). Dock your iPod by sliding your iPod on top of the iM600 docking station. If necessary, first install the docking adapter that came with your iPod. While the docking
adapter is not required for proper functioning of your iPod and iM600, it will provide a better fit.
September 22, 2010 | Posted in Audio Video, Electronic Manual | Leave a Comment
Overhead Mounting Video and DVD Player Cars PDF Installation Instructions Manual
Remove dome light from the center of the ceiling behind the front seats. The clear cover will usually snap off and the fixture will usually be mounted with screws. Unplug the factory dome light. Remove one set of side molding to allow viewing and proper location of center cross beam under the headliner. Mark and cut a tiny hole in the center to verify your beam location.
Remove the overhead mounting plate to use as a template for marking your ceiling headliner audio player. Use the mounting plate to line up and center over the support beam and cut out. Use super soft leaded pencil to draw a line around the mounting bracket top outline. (be careful not to use the wrong side of the bracket; have the mounting feet side facing down and the arrow pointing toward the rear of the vehicle.
July 28, 2010 | Posted in Audio Video, Electronic Manual | Leave a Comment
Asus Xonar D2X Audio Card PDF Quick Installation Guide
Installation requirements
To ensure a successful installation of the Xonar D2X audio card, your computer must meet the following requirements:
One PCI Express 1.0 (or higher) compatible slot for the audio card
One available 4-pin power cable from PC’s power supply unit
Microsoft® Windows® Vista/XP(32/64bit)/MCE2005
Intel® Pentium® 4 1.4GHz or AMD Athlon 1400 CPU or faster CPU
> 256 MB DRAM system memory
> 60 MB available HDD space for driver installation package; > 200MB space available for Ableton Live and > 320MB for Cakewalk package
CD-ROM drive (or DVD-ROM drive) for software installation
High-quality headphones, powered analog speakers, or digital speakers with Dolby Digital or DTS decoders to enjoy the Ultra-High Fidelity sounds of the
July 4, 2010 | Posted in Asus Manual, Audio Video | Leave a Comment
Pie Niss/Nav-Eye1 Navigation Video Interface PDF Manual Guide
1. Disconnect the negative battery terminal
2. Completely remove the factory navigation monitor
3. Locate the 24-pin connector behind the monitor
4. Disconnect the 24-pin from the monitor
5. Connect the 24-pin male plug of the NISS/AV-EYE1 into the monitor
6. Connect the 24-pin female connector to the factory harness
7. Find a location for the NISS/NAV-EYE1 converter box, cable length is 6’ long.
8. Reinstall the navigation monitor back into the dash console
9. Route the DB9-pin connector into the NISS/NAV-EYE1converter box
10. Connect the DB9-pin connector into the NISS/NAV-EYE1 converter box, make sure you hand-tighten the locking screws.
11. Connect power and ground wires (Black/White is 12V ignition and BLK is Ground) of the NISS/NAV-EYE1 converter box.
INSTALLATION FOR CAMERA INPUT (Connections to the NISS/NAV-EYE1)
1. Make sure back-up camera is properly installed (installation not covered by these installations)
2. Connect the WHITE wire Ground and BLUE wire to reverse +12V signal
3. Connect the camera video output to “VIDEO 2” of the NISS/NAV-EYE1 converter
4. Set RGBS/RGSB switch to RGBS position.
June 4, 2010 | Posted in Audio Video, Electronic Manual | Leave a Comment
Motorola S9 Bluetooth Active Headphones PDF User Manual
Pairing Your S9 with Your Bluetooth Device(s) Before you can use your S9, you must pair (link) it with your Bluetooth-enabled phone and/or music devices. “Pairing” links devices equipped with Bluetooth wireless technology and allows a previously linked device to remember your S9. Once devices are paired, they automatically connect when turned on and within range. First Time Use When using your S9 for the first time, follow these steps to pair (connect) to your Bluetooth device(s): Important: If you are pairing separate Bluetooth devices for handsfree calls and streaming music, it is recommended that you pair your S9 with your handsfree device (phone) first. 1 Ensure the Bluetooth feature is enabled (turned on) in your device. (Refer to your phone or music device manual for detailed instructions on enabling Bluetooth)
March 13, 2010 | Posted in Audio Video, Bluetooth Manual, Electronic Manual, Motorola Manual | Leave a Comment